Plumbing Essentials: An Essential for When Installing a Bathtub
Plumbing Essentials: An Essential for When Installing a Bathtub
Blog Article
Each person has got their private opinion with regards to Installing A Bathtub.
Installing a tub isn't precisely brain surgery, but it does need solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a reasonably hard project. If the old tub is conveniently available, the project can move speedily; if you have to open up a wall to eliminate the old bathtub and place the brand-new bathtub, the task is a lot harder. In either instance, the project is within a home handyman's abilities, although you will require a helper to move out the old tub and also set in the brand-new one. Ensure you have certified on your own for the job and also are comfortable attempting it. Rather than employing a contractor to take control of a halfway-completed task, it is far better to consider utilizing one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This article will aid you install a new bath tub in your shower room if you have actually currently bought a brand-new bathtub and also do not need to change the arrangement of your previous water pipelines.
Your devices as well as product list should consist of the following:
Getting ready for the Installment
Firstly, the supporting framework supplied with the bathroom must be fitted (if required) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is essential to make sure that if the tap features a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets unit to prevent stress on the tub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you use all of the provided washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its final setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you need to do is separate the water supply. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of removing the existing faucets can be quite troublesome due to the restricted access that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a towel all set for the staying water that will come from the pipes. As soon as the supply pipes have actually been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Before going on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Utilizing both wooden boards under its feet, place the bathtub in the needed placement. The wooden boards are practical in evenly spreading the weight of the tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the level and also changing the feet on the bathtub till the level checks out level.
To set up taps, fit all-time low of the furthest flexible faucet port to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Turn on the water supply and also check all joints as well as brand-new pipework for leaks as well as tighten them if needed. Fill the bathtub as well as also inspect the overflow electrical outlet and the normal electrical outlet for leaks.
Lastly, deal with the bath paneling as defined in the maker's instruction manual. Tiling and also sealing around the bathtub ought to wait up until the bath tub has actually been made use of a minimum of once as this will resolve it into its last placement.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in location in between the tap and also the sink. Protect the faucet in place with the maker supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former type must be attached to the tap ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to break a stiff seal, causing the water to penetrate the wall between the bath and the tiling, resulting in problems with dampness and possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components as well as fittings. They are offered in tubes and cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the bathtub with water before securing, to permit the activity experienced when the tub remains in use. The sealer can crack relatively very early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the market. It is advisable to fit the tiles using waterproof or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader about How to Install a Bathtub Yourself, I figured sharing that excerpt was worthwhile. Do you know about somebody else who is excited about the subject? Take a moment to promote it. Many thanks for your time spent reading it.
Plumbing challenges? Get immediate solutions. Report this page